 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PHOTOCOUPLER PS9303L,PS9303L2 1 Mbps TOTEM POLE OUTPUT TYPE HIGH CMR, IPM DRIVER 6-PIN SDIP PHOTOCOUPLER DESCRIPTION The PS9303L and PS9303L2 are optical coupled high-speed, totem pole output (active high output type) isolators containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9303L and PS9303L2 are specified high CMR and pulse width distortion with operating temperature. It is suitable for IPM drive. The PS9303L is lead bending type (Gull-wing) for surface mounting. The PS9303L2 is lead bending type for long creepage distance (Gull-wing) for surface mount. NEPOC Series FEATURES * High common mode transient immunity (CMH, CML = 15 kV/ s MIN.) * Half size of 8-pin DIP * Pulse width distortion ( tPLH * High-speed (1 Mbps) * High isolation voltage (BV = 5 000 Vr.m.s.) * Totem pole output (Active High Output Type) APPLICATIONS * IPM Driver * General purpose inverter TRUTH TABLE LED ON OFF Output H L Document No. PN10694EJ04V0DS (4th edition) Date Published September 2009 NS The mark PS9303L,PS9303L2 PACKAGE DIMENSIONS (UNIT: mm) Lead Bending Type (Gull-wing) For Surface Mount Lead Bending Type (Gull-wing) For Long Creepage Distance (Surface Mount) 2 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 PHOTOCOUPLER CONSTRUCTION Parameter Air Distance (MIN.) Outer Creepage Distance (MIN.) Isolation Distance (MIN.) PS9303L 7 mm 7 mm 0.4 mm PS9303L2 8 mm 8 mm 0.4 mm MARKING EXAMPLE Data Sheet PN10694EJ04V0DS 3 PS9303L,PS9303L2 ORDERING INFORMATION Part Number Order Number Solder Plating Specification PS9303L PS9303L-E3 PS9303L2 PS9303L2-E3 PS9303L-V PS9303L-V-E3 PS9303L2-V PS9303L2-V-E3 PS9303L-AX PS9303L-E3-AX PS9303L2-AX PS9303L2-E3-AX PS9303L-V-AX PS9303L-V-E3-AX PS9303L2-V-AX PS9303L2-V-E3-AX Pb-Free (Ni/Pd/Au) 20 pcs (Tape 20 pcs cut) Embossed Tape 2 000 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 2 000 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 2 000 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 2 000 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) PS9303L2 PS9303L Packing Style Safety Standard Approval Standard products (UL, CSA approved) PS9303L2 Application Part Number*1 PS9303L *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25 C, unless otherwise specified) Parameter Diode Forward Current *1 Symbol IF VR VCC Ratings 20 5 0.5 to +25 Unit mA V V Reverse Voltage Detecto r Supply Voltage Output Voltage Output Current Power Dissipation Isolation Voltage *3 *2 VO IO PC BV TA Tstg 0.5 to +25 25 210 5 000 40 to +100 55 to +125 V mA mW Vr.m.s. C C Operating Ambient Temperature Storage Temperature *1 Reduced to 0.33 mA/ C at TA = 70 C or more. *2 Reduced to 4.0 mW/ C at TA = 70 C or more. *3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output. Pins 1-3 shorted together, 4-6 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Supply Voltage Output Voltage Input Current (ON) Input Voltage (OFF) Symbol VCC VO IF (ON) VF (OFF) MIN. 4.5 0 6 0 TYP. 15 MAX. 20 20 10 0.8 Unit V V mA V 4 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 ELECTRICAL specified) CHARACTERISTICS (TA = 40 to +100 C, VCC = 4.5 to 20 V, unless otherwise Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Voltage Symbol VF IR Ct VOH Conditions IF = 10 mA, TA = 25 C VR = 3 V, TA = 25 C V = 0 V, f = 1 MHz, TA = 25 C VCC = 5 V, IO = 3.5 mA, IF = 10 mA VCC = 20 V, IO = 3.5 mA, IF = 10 mA MIN. 1.2 TYP.*1 1.6 MAX. 1.9 10 Unit V A pF V 30 2.4 17.4 3.5 18.1 0.1 1.6 1.8 2.7 2.9 7 40 0.35 2.7 3 3.7 4 Low Level Output Voltage *2 VOL ICCH IO = 3.5 mA, VF = 0 V VCC = 5 V, IF = 10 mA VCC = 20 V, IF = 10 mA V mA High Level Supply Current Low Level Supply Current ICCL VCC = 5 V, VF = 0 V VCC = 20 V, VF = 0 V mA High Level Output Short Circuit Current Low Level Output Short Circuit Current Coupled Threshold Input Current Isolation Resistance Isolation Capacitance Propagation Delay Time (H L)*3 Propagation Delay Time (L H)*3 Pulse Width Distortion (PWD) Rise Time (10-90%)*3 Fall Time (90-10%)*3 IOSH VCC = 20 V, VO = GND, IF = 10 mA mA IOSL VCC = VO = 20 V, VF = 0 V 7 40 mA IFLH RI-O CI-O tPHL VCC = 5 V, VO > 2.4 V, IO = 3.5 mA VI-O = 500 VDC, RH = 60%, TA = 25 C V = 0 V, f = 1 MHz, TA = 25 C VCC = 20 V, CL = 100 pF, IF = 10 0 mA, VTHHL = 1.3 V VCC = 20 V, CL = 100 pF, IF = 0 10 mA, VTHLH = 1.3 V VCC = 20 V, CL = 100 pF, IF = 10 0 mA VCC = 20 V, CL = 100 pF, IF = 0 10 mA VCC = 20 V, CL = 100 pF, IF = 10 0 mA 15 50 10 12 2.4 5 mA 0.6 185 550 pF ns tPLH 50 240 500 ns tPLH-tPHL 55 350 ns tr 120 ns tf 90 ns Common Mode Transient Immunity at High Level Output*4 Common Mode Transient Immunity at Low Level Output*4 CMH VCC = 5 V, TA = 25 C, IF = 10 mA, VCM = 1.5 kV, VO (MIN.) = 2.4 V kV/ s CML VCC = 5 V, TA = 25 C, IF = 0 mA, VCM = 1.5 kV, VO (MAX.) = 0.35 V 15 kV/ s Data Sheet PN10694EJ04V0DS 5 PS9303L,PS9303L2 *1 Typical values at TA = 25 C. *2 Because VO of 2.4 V may be output when the LED current is not input and when output supply of VCC = 4.5 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time *4 Test circuit for common mode transient immunity USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of more than 0.1 3. Pin 2 (which is an NC *1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. pin) can either be connected directly to the GND pin on the LED side or left open. Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this may degrade the internal noise environment of the device. *1 NC: Non-connection (No connection) 4. Avoid storage at a high temperature and high humidity. 6 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified) Remark The graphs indicate nominal characteristics. Data Sheet PN10694EJ04V0DS 7 PS9303L,PS9303L2 Remark The graphs indicate nominal characteristics. 8 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 TAPING SPECIFICATIONS (UNIT: mm) Data Sheet PN10694EJ04V0DS 9 PS9303L,PS9303L2 10 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) Data Sheet PN10694EJ04V0DS 11 PS9303L,PS9303L2 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220 C * Time to preheat temperature from 120 to 180 C * Number of reflows * Flux 260 C or below (package surface temperature) 10 seconds or less 60 seconds or less 120 30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260 C or below (molten solder temperature) 10 seconds or less 120 C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron * Peak temperature (lead part temperature) * Time (each pins) * Flux 350 C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100 C. 12 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler's input and output or between V CC and GND at startup, the output side may enter the on state, even if the voltage is within the absolute maximum ratings. Data Sheet PN10694EJ04V0DS 13 PS9303L,PS9303L2 SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Climatic test class (IEC 60068-1/DIN EN 60068-1) Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.5 UIORM, Pd 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 UIORM, Pd 5 pC Highest permissible overvoltage Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11)) Material group (DIN EN 60664-1 VDE0110 Part 1) Storage temperature range Operating temperature range Isolation resistance, minimum value VIO = 500 V dc at TA = 25C VIO = 500 V dc at TA MAX. at least 100C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = Tsi Tstg TA CTI Symbol Spec. 40/100/21 Unit UIORM Upr 1 130 1 695 Vpeak Vpeak Upr 2 119 Vpeak UTR 8 000 2 175 III a -55 to +125 -40 to +100 1012 1011 Vpeak C C Ris MIN. Ris MIN. Tsi Isi Psi Ris MIN. 175 400 700 109 C mA mW 14 Data Sheet PN10694EJ04V0DS PS9303L,PS9303L2 Data Sheet PN10694EJ04V0DS 15 PS9303L,PS9303L2 Caution This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. GaAs Products |
Price & Availability of PS9303L-E3-AX
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |